LIVE READINGS
Bowl Speed0RPM
Feed Temperature45°C
Throughput0l/h
Back Pressure0.0bar
Vibration0.0mm/s
Sludge Tank0%
MODE: FO PURIFIER
Target RPM9000
Target Temp98°C
Rated Throughput6500 l/h
Shot Interval30 min
Gravity DiscMEDIUM
PURIFIER P&ID SCHEMATIC
BOWL 0 RPM MOTOR FO/LO INLET HEATER 45°C FP CLEAN OIL OUTLET BP SLUDGE/WATER SLUDGE TANK 0% SEAL WATER VIBRATION 0.0 mm/s OIL/WATER INTERFACE WATER OIL CORRECT SCENARIO: -- Select scenario to begin
ALARM MANAGEMENT
SHOT TIMER
--:--
Next auto desludge
ACTIVE ALARMS
VALVE LINEUP
PROCESS VALVES
HEATING STEAM
RPM TREND & SHOT LOG
SHOT LOG:
SCENARIO / EVENT LOG
READY
Select a scenario from the start modal to begin training.
PURIFIER — FULL P&ID
PURIFIER CONTROLS
MOTOR
Status STOPPED
Bowl Speed 0 RPM
FEED PUMP
Feed Pump OFF
THROUGHPUT
Set Point 5000 l/h
10006500 l/h
GRAVITY DISC
PIPELINE COMPONENTS
SEPARATOR BOWL — DISC STACK & INTERNALS
BOWL STATUS
BOWL SPEED
Current RPM 0 RPM
Target RPM 9000 RPM
Motor Current 0.0 A
DISC STACK
Disc Count 96
Half Angle 35°
Stack Condition GOOD
OIL/WATER INTERFACE
Interface Position CORRECT
Gravity Disc MEDIUM
Fuel Density 0.991 g/ml
VIBRATION
Level 0.0 mm/s
Alarm Limit 7.5 mm/s
Trip Limit 12.5 mm/s
FEED SYSTEM — PUMP, HEATER & VALVES
FEED CONTROLS
FEED PUMP
Status OFF
Throughput 0 l/h
FLOW RATE
10006500 l/h
INLET VALVE
FO/LO Inlet CLOSED
OUTLET VALVE
Clean Oil Out CLOSED
Back Pressure 0.0 bar
HEATING SYSTEM — STEAM HEATER & TEMPERATURE CONTROL
HEATING CONTROLS
FEED TEMPERATURE
Current 45°C
Target (FO) 98°C
Target (LO) 55°C
High Alarm 105°C
STEAM SUPPLY
Steam Valve CLOSED
Steam Pressure 0.0 bar
SEAL WATER
Seal Water Valve CLOSED
Flow 0.0 l/min
SLUDGE SYSTEM — SLUDGE TANK & DISCHARGE
SLUDGE CONTROLS
SLUDGE TANK
Level 0%
High Alarm 85%
High-High Trip 95%
SLUDGE OUTLET
Sludge Valve CLOSED
MARPOL COMPLIANCE
MEPC.1/Circ.642 applies
Record all sludge transfers
Oil Record Book Part I
Code 16 — Transfer to reception
CLEAN OIL DISCHARGE — BACK PRESSURE & OUTLET
DISCHARGE CONTROLS
CLEAN OIL OUTLET
Outlet Valve CLOSED
Back Pressure 0.0 bar
Flow Rate 0 l/h
BACK PRESSURE VALVE
Set Point 0.3 bar
Actual 0.0 bar
Status IDLE
SERVICE TANK
Destination HFO SERVICE
Transfer Rate 0 l/h
DESLUDGE — BOWL SHOT SEQUENCE
DESLUDGE CONTROLS
SHOT TRIGGER
Auto Interval 30 min
Next Auto Shot --:--
Shot Count 0
SHOT LOG
SEQUENCE INFO
1. Reduce water supply
2. Open drain valve
3. Discharge ports open
4. Sludge expelled centrifugally
5. Ports close, re-seal water
6. Resume normal operation
AUTOMATIC CONTROL — SLUDGE TIMER & SAFETY TRIPS
AUTO CONTROL SETTINGS
OPERATING MODE
AUTO DESLUDGE
Auto Shot ENABLED
Interval 30 min
Timer --:--
SAFETY TRIPS
High Vibration 12.5 mm/s → STOP
High Temperature 105°C → ALARM
Sludge Tank HH 95% → STOP
Bowl Underspeed -10% → ALARM
START PERMISSIVES
Feed temperature ≥ set point
Process valves open
Seal water flowing
Sludge tank level < 85%
PROCESS TRENDS — RPM · TEMPERATURE · VIBRATION · THROUGHPUT
BOWL SPEED (RPM)
FEED TEMPERATURE (°C)
VIBRATION (mm/s)
THROUGHPUT (l/h)
TREND WINDOW:

Screen Too Small

This simulator requires a minimum resolution of 980 x 600 px.
Recommended: 1920 x 1080 (16:9) or larger.
Please resize your browser window or use a larger display.